- #CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC HOW TO#
- #CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC INSTALL#
- #CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC PLUS#
- #CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC FREE#
Here is a useful article on using NMAP from the command line. It can be used with a graphical user interface of as a command line tool.
#CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC INSTALL#
You can install NMAP on windows,Linux and Apple. You can check the port status of remote machines using a port scanner line nmap.
#CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC HOW TO#
These articles show you how to use netstat on windows and on linux. Windows and Linux systems have a utility called netstat which will give you a list of open ports on your computer. Here is a very good video that explains ports and sockets really well It can use any port, but the web server application is designed to use a TCP connection.
It has no has built in error checking and will not re transmit missing packets.Īpplications are designed to use either the UDP or TCP transport layer protocol depending on the type of connection they require.įor example a web server normally uses TCP port 80. UDP – is for connection less applications. It has built in error checking and will re transmit missing packets. TCP – is for connection orientated applications. The TCP/IP protocol supports two types of port- TCP Port and UDP Port. Ports are implemented at the transport layer as part of the TCP or UDP header as shown in the schematic below: IP addresses are implemented at the networking layer which is the IP layer. Note: You may find reading the article on the TCP/IP protocol suite useful to understand the following Client port numbers are dynamically assigned, and can be reused once the session is closed.
#CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC PLUS#
TCP SocketsĪ connection between two computers uses a socket.Ī socket is the combination of IP address plus port When a Web browser connects to a web server the browser will allocate itself a port in this range.
#CANNOT CONNECT TO STREET SMART EDGE THROUGH CITRIX ON MAC FREE#
Ports 49152-65535– These are used by client programs and you are free to use these in client programs.
User written programs should not use these ports. Ports 1024-49151- Registered Port -These can be registered for services with the IANA and should be treated as semi-reserved. e.g Web servers normally use port 80 and SMTP servers use port 25 (see diagram above). These are allocated to server services by the Internet Assigned Numbers Authority (IANA). Port numbers are divided into ranges as follows: Port Number Ranges and Well Known PortsĪ port number uses 16 bits and so can therefore have a value from 0 to 65535 decimal However each apartment also has an apartment number which corresponds to the Port number. If you use a house or apartment block analogy the IP address corresponds to the street address.Īll of the apartments share the same street address. The diagram below shows a computer to computer connection and identifies the IP addresses and ports. The use of ports allow computers/devices to run multiple services/applications.
Just as the IP address identifies the computer, The network port identifies the application or service running on the computer. However an IP address alone is not sufficient for running network applications, as a computer can run multiple applications and/or services. The IP address identifies the device e.g. So the Set-Cookie didn’t apply.On a TCP/IP network every device must have an IP address. The Created Cookie by StoreFront was bind too the /Citrix/StoreWeb/ path, instead of /Citrix/StoreWeb. So the blog from nerdscaler was good, but the problem was the “/” at the end from the Set-Cookie. But the noticed that it wasn’t working with Firefox and Internet Explorer.Īfter some troubleshooting I found the solution you using the next rewrite:Īdd rewrite action RW_ACT_INS_HTTP_HEADER-ExpireSmartCardCookie insert_http_header Set-Cookie “\”CtxsSmartcardAuthenticated=xyz Path=/Citrix/ StoreWeb / expires=Wednesday, 0 23:12:40 GMT Secure\””Īdd rewrite policy RW_POL_INS_HTTP_HEADER-ExpireSmartCardCookie “.SET_TEXT_MODE(IGNORECASE).EQ(\”/Citrix/ StoreWeb/logout.aspx\”)” RW_ACT_INS_HTTP_HEADER-ExpireSmartCardCookieīind vpn vserver VSSERVERNAME -policy RW_POL_INS_HTTP_HEADER-ExpireSmartCardCookie -priority 100 -gotoPriorityExpression NEXT -type RESPONSE This blog describes the problem and also a fix. One of the issues I had was the error: You cannot log on using a smart card.ĭoing some research on the internet I found a blog from (). Today I did a Citrix Federated Authentication Services (FAS) implementation at a customer.
0 kommentar(er)
